specification model dc voltage rated current rated power output line regulation load regulation setup, rise time note.6 hold up time (typ.) voltage range note.5 frequency range power factor (typ.) efficiency (typ.) ac current (typ.) input inrush current( .) typ leakage current safety standards working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current note.4 over voltage over temperature 2000ms, 200ms / 115vac 000ms, 200ms / 230vac at full load at full load 1 16ms at full load 230vac /115vac 90 ~ 305vac 127 ~ 431vdc 47 ~ 63hz cold start 70a/230vac <0.75ma / 277vac 95 ~ 108% protection type : constant current limiting, recovers automatical ly after fault condition is removed compliance to en55015, en61000-3-2 class c ( 60% load, 12v model 65% loa d) ; en61000-3-3 compliance to en61000-4-2,3,4,5,6,8,11, en61547, en55024, lig ht industry level (surge 4kv), criteria a 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 12min./1cycle, period for 72min. each along x, y, z axes 316.2khrs min. mil-hdbk-217f (25 ) 167*53*29.5mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. constant current operation region is within 60% ~100% rated output vol tage. this is the suitable operation region for led related application s, but please reconfirm special electrical requirements for some specific syste m design. 5. derating may be needed under low input voltages. please check the static c haracteristics for more details. 6. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. 7. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by t he complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 8. heat sink hs1,hs2 can not be shorted. 0.27kg; 36pcs/11.2kg/0.67cuft protection type : shut down o/p voltage, re-power on to recover 80w single output switching power supply universal ac input / full range (up to 305vac)built-in active pfc function protections: short circuit / over current / over voltage / over temperature cooling by free air convection output constant current level adjustable three in one dimming function (1~10vdc or pwm signal or resistance) suitable for built in led lighting system 3 years warranty suitable for dry / damp locations class 2 power unit100% full load burn-in test features : h l p - 8 0 h s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & emc protection 95 10 (rth2) protection type : shut down o/p voltage, re-power on to recover 14 ~ 17v 59 ~ 68v 87.5% 88.5% 89.5% 90% 90% 90% 90% 90% 90% 2.5% 2.0% 1.0% 1.0% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 2.0% 1.5% 1.0% 0.5% 0.5% 0.5% 0.5% 1.0% 0.5% 0.5% 1.0% 0.5% 0.5% 12v hlp-80h-12 hlp-80h-15 hlp-80h-20 hlp-80h-24 hlp-80h-30 h lp-80h-36 hlp-80h-42 hlp-80h-48 hlp-80h-54 15v 20v 24v 30v 36v 48v 5a 5a 4a 3.4a 2.7a 2.3a 1.7a 60w 75w 80w 81.6w 81w 82.8w 81.6w 150mvp-p 150mvp-p 150mvp-p 150mvp-p 200mvp-p 200mvp-p 200mvp-p 54v 1.5a 81w 200mvp-p 42v 1.95a 81.9w 200mvp-p pf>0.96/115vac, pf>0.96/230vac, pf>0.94/277vac at full load (pl ease refer to "power factor characteristic" curve) 0.85a / 115vac 0.425a / 230vac 0.4a / 277vac 7.2 ~12v 9 ~ 15v 12 ~ 20v 14.4 ~ 24v 18 ~ 30v 21.6 ~ 36v 28.8 ~ 48v 32.4 ~ 54v 25.2 ~ 42v constant current region note.4 withstand voltage isolation resistance i/p-o/p:3.75kvac i/p-fg:1.88kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh -40 ~ +70 (refer to "derating curve") emc immunity emc emission file name:hlp-80h-spec 2012-03-01 selv m m voltage adj. range current adj. range can be adjusted by internal potentiometer or through output connecto r 4 ~ 5a 4 ~ 5a 3.2 ~ 4a 2.72 ~ 3.4a 2.16 ~ 2.7a 1.84 ~ 2.3a 1.36 ~ 1.7a 1.2 ~ 1.5a 1.56 ~ 1.95a 13.5 ~ 17v 17 ~ 22v 22 ~ 27v 27 ~ 33v 33 ~ 40v 43 ~ 53v 10.8 ~ 13.5v 49 ~ 58v 38 ~ 46v ( except for 48v,54v ) ( for 48v,54v only) short circuit hiccup mode, recovers automatically after fault condition is remove d ul8750, csa c22.2 no. 250.0-08 (except for 48v, 54v), en61347-1, en613 47-2-13 approved ; design refer to ul60950-1, tuv en60950-1 18 ~ 24v 23 ~ 30v 28 ~ 35v 35 ~ 43v 41 ~ 49v 54 ~ 63v 48 ~ 58v
mechanical specification unit:mm fosc : 100khz block diagram ac input connector (cn1) : jst b6p-vh or equivalent pin no. 13 6 2,4,5 assignment ac/l ac/n fg no pin mating housing jst vhr jst svh-21t-p1.1 or equivalent or equivalent terminal dc output connector (cn2) : jst b6p-vh or equivalent pin no. 12 3,4 5,6 assignment dim+(vr1) dim-(vr2) +v -v mating housing jst vhr or equivalent terminal jst svh-21t-p1.1 or equivalent 3max. dim+ dim- detection pwm & pfc circuit o.l.p. o.t.p. emi filter rectifiers power switching filter & rectifiers +v -v i/p fg control o.v.p. & o.l.p. pfc circuit hs1 hs2 230vac input only ambient temperature ( ) -40 -25 0 -10 15 30 50 60 70 20 40 50 60 80 100 (horizontal) derating curve static characteristics input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 305 100 90 80 70 60 50 40 load (%) : grounding required 80w single output switching power supply h l p - 8 0 h s e r i e s file name:hlp-80h-spec 2012-03-01 29.5max. 53 43 4- 3.5 t3.15a/300v /350v cn2 fs1 svr1 53 42 1 6 53 42 1 6 cn1 svr2 3.5 159.5 167 5 hs1,hs2 can not be shorted
70 72 74 76 78 80 82 84 86 88 90 92 94 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277vac 230vac 115vac 0 .9 2 0 .9 3 0 .9 4 0 .9 5 0 .9 6 0 .9 7 0 .9 8 0 .9 9 1 5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 % 2 7 7 v a c 2 3 0 v a c 1 1 5 v a c pf load constant current mode hlp-80h series possess superior working efficiency that up to 90% can be re ached in field applications. load efficiency (%) efficiency vs load (48v model) (80w) 80w single output switching power supply h l p - 8 0 h s e r i e s file name:hlp-80h-spec 2012-03-01 power factor characteristic there are two major kinds of led drive method "direct drive" and "with led driv er". typical led power supply i-v curve a typical led power supply may either work in "constant voltage mode (cv) or c onstant current mode (cc)" to drive the leds. mean well's led power supply with cv+ cc characteristic can b e operated at both cv mode (with led driver, at area (a) and cc m ode (direct drive, at area (b). driving methods of led module vo(%) 100 60 50 95 (max.) io (%) constant voltage area constant current area hiccup protection (a) (b) (c)
80w single output switching power supply h l p - 8 0 h s e r i e s file name:hlp-80h-spec 2012-03-01 dimming operation 60k 60% 60% 10k 10k /n 20k /n 30k /n 40k /n 50k /n 60k /n 70k /n 80k /n 90k /n 100k /n single driver multiple drivers (n=driver quantity for synchronized dimming operation) 1v 4v 7v 2v 5v 8v 3v 6v 9v 10v 10% 10% 20k 20% 20% 30k 30% 30% 40k 40% 40% 50k 50% 50% 70k 70% 70% 80k 80% 80% 90k 100k open open open 90% 90% 100% 100% resistance value dimming value percentage of rated current percentage of rated current reference resistance value for output current adjustment (typical ) please do not connect "dim-" to "-v". 1 ~ 10v dimming function for output current adjustment (typical) 60% 60% 10% 10% 20% 20% 30% 30% 40% 40% 50% 50% 70% 70% 80% 80% 90% 90% 100% 100% duty value percentage of rated current 102%~108% ----- 102%~108% 102%~108% 10v pwm signal for output current adjustment (typical): frequency ra nge :100hz ~ 3khz built-in 3 in 1 dimming function, output constant current level can be adju sted through output connector by 1~10vdc, pwm signal, or connecting a resistance between dim+ and dim-. n fg l relay blue brown green/ yellow ac/l ac/n hlp-80h dim+ dim- v(-) v(+) blue white black red switch adjuster 0~100k ohms resistance 1~10v dc voltage 10v pwm signal dimming connection diagram for turning the lighting fixture on/off : using the built-in dimming function can't turn the lighting fixture tot ally dark. please refer to the connection method below to achieve 0% bright ness of the lighting fixture connecting to the led power supply unit. led lighting fixture -v +v +v dim- dim+ -v ac/n ac/l fg using a switch and relay can turn on/off the lighting fixture. 1.output constant current level can be adjusted through output cable by c onnecting a or 1~10vdc or 10v pwm signal between dim+ and dim-. resistance 2.the led lighting fixture can be turned on/off by the switch.
|
